CogFindCircle.NumToIgnore Property

CogFindCircle NumToIgnore Property

Cognex VisionPro

The number of points that will be ignored in the fitting operation. If DecrementNumToIgnore is true then the number of points ignored is actually (NumToIgnore - Number of calipers that found no edge).

Namespace: Cognex.VisionPro.Caliper
Assembly: Cognex.VisionPro.Caliper (in Cognex.VisionPro.Caliper.dll) Version: 65.1.0.0

Syntax

C++

Copy to Clipboard Print

public int NumToIgnore { get; set; }

public int NumToIgnore { get; set; }

Public Property NumToIgnore As Integer 
	Get 
	Set

Public Property NumToIgnore As Integer 
	Get 
	Set

public:
property int NumToIgnore {
	int get ();
	void set (int value);
}

public:
property int NumToIgnore {
	int get ();
	void set (int value);
}

Property Value

Type: Int32

Events

Event Type	Reason
CogFindCircle Changed	Fires when the value of this property changes. The following state flag may be affected: SfNumToIgnore
CogFindCircle Changed	Fires when both this property and NumCalipers change. The following state flags may be affected: SfNumCalipers SfNumToIgnore

Event Type

Reason

CogFindCircle Changed

Fires when the value of this property changes.

The following state flag may be affected:

SfNumToIgnore

CogFindCircle Changed

Fires when both this property and NumCalipers change.

The following state flags may be affected:

Exceptions

Exception	Condition
ArgumentException	A value of less than 0 was supplied.

Remarks

The number of points that will be ignored in the fitting operation. If DecrementNumToIgnore is true then the number of points ignored is reduced by the number of calipers which failed to detect an edge.

If the value of this property is changed such that the number of calipers minus the number of points to ignore is less than 3, NumCalipers will be changed so that the difference is 3 and the change event will indicate that both properties have changed.

Default Value: 0

Examples

Copy to Clipboard Print

' Create a CogFindCircle operator and a results object
Dim myFCO As New CogFindCircle
Dim myFCOResults As New CogFindCircleResults

' Configure the CogFindCircle Object
myFCO.ExpectedCircularArc = myArc
myFCO.CaliperRunParams.FilterHalfSizeInPixels = 3
myFCO.NumCalipers = 10
myFCO.CaliperProjectionLength = 25
myFCO.CaliperSearchLength = 35
myFCO.CaliperSearchDirection = CogFindCircleSearchDirectionConstants.Inward

myFCO.DecrementNumToIgnore = True
myFCO.RadiusConstraint = myArc.Radius
myFCO.RadiusConstraintEnabled = True

' Execute it
myFCOResults = myFCO.Execute(myAFT.OutputImage)

' Display the found circle
CogDisplay1.StaticGraphics.Clear()
CogDisplay1.StaticGraphics.Add(myFCOResults.GetCircle, "")

' Display some information about the result
lblRes.Text = "Points found; " & myFCOResults.NumPointsFound _
                                & " points used; " & myFCOResults.NumPointsUsed _
                                & " RMS error: " & myFCOResults.RMSError

' Create a CogFindCircle operator and a results object
Dim myFCO As New CogFindCircle
Dim myFCOResults As New CogFindCircleResults

' Configure the CogFindCircle Object
myFCO.ExpectedCircularArc = myArc
myFCO.CaliperRunParams.FilterHalfSizeInPixels = 3
myFCO.NumCalipers = 10
myFCO.CaliperProjectionLength = 25
myFCO.CaliperSearchLength = 35
myFCO.CaliperSearchDirection = CogFindCircleSearchDirectionConstants.Inward

myFCO.DecrementNumToIgnore = True
myFCO.RadiusConstraint = myArc.Radius
myFCO.RadiusConstraintEnabled = True

' Execute it
myFCOResults = myFCO.Execute(myAFT.OutputImage)

' Display the found circle
CogDisplay1.StaticGraphics.Clear()
CogDisplay1.StaticGraphics.Add(myFCOResults.GetCircle, "")

' Display some information about the result
lblRes.Text = "Points found; " & myFCOResults.NumPointsFound _
                                & " points used; " & myFCOResults.NumPointsUsed _
                                & " RMS error: " & myFCOResults.RMSError

C++

Copy to Clipboard Print

// Create a CogFindCircle operator and a results object
    CogFindCircle myFCO = new CogFindCircle();

    CogFindCircleResults myFCOResults = new CogFindCircleResults();

// Configure the CogFindCircle Object
myFCO.ExpectedCircularArc = myArc;
myFCO.CaliperRunParams.FilterHalfSizeInPixels = 3;
myFCO.NumCalipers = 10;
myFCO.CaliperProjectionLength = 25;
myFCO.CaliperSearchLength = 35;
myFCO.CaliperSearchDirection = CogFindCircleSearchDirectionConstants.Inward;

myFCO.DecrementNumToIgnore = true;
myFCO.RadiusConstraint = myArc.Radius;
myFCO.RadiusConstraintEnabled = true;

// Execute it
myFCOResults = myFCO.Execute((CogImage8Grey) myAft.OutputImage);

// Display the found circle
CogDisplay1.StaticGraphics.Clear();
CogDisplay1.StaticGraphics.Add(myFCOResults.GetCircle(), "");

// Create a CogFindCircle operator and a results object
    CogFindCircle myFCO = new CogFindCircle();

    CogFindCircleResults myFCOResults = new CogFindCircleResults();

// Configure the CogFindCircle Object
myFCO.ExpectedCircularArc = myArc;
myFCO.CaliperRunParams.FilterHalfSizeInPixels = 3;
myFCO.NumCalipers = 10;
myFCO.CaliperProjectionLength = 25;
myFCO.CaliperSearchLength = 35;
myFCO.CaliperSearchDirection = CogFindCircleSearchDirectionConstants.Inward;

myFCO.DecrementNumToIgnore = true;
myFCO.RadiusConstraint = myArc.Radius;
myFCO.RadiusConstraintEnabled = true;

// Execute it
myFCOResults = myFCO.Execute((CogImage8Grey) myAft.OutputImage);

// Display the found circle
CogDisplay1.StaticGraphics.Clear();
CogDisplay1.StaticGraphics.Add(myFCOResults.GetCircle(), "");