In-Sight 2000 Vision Sensor Specifications

Specifications 2000-110 2000-120/120C 2000-130/130C 2000-23M 2000-230/230C 2001-230/230C
Minimum Firmware Version1

In-Sight 2000-110/120/130: In-Sight 5.2.1

In-Sight 2000-120C/130C: In-Sight 5.3.0

In-Sight 2000-23M: In-Sight 5.5.0

In-Sight 2000-230/230C: In-Sight 5.6.0

In-Sight 2001-230/230C: In-Sight 5.6.0
Memory

Job/Program: 32MB non-volatile flash memory; unlimited storage via remote network device

Image Processing: 128MB SDRAM
Imager 1/3-inch CMOS, 4.80 mm x 3.60 mm (W x H), 3.75 μm sq. pixels
Lens

S-Mount/M12, standard 8mm, optional 3.6mm, 6mm, 12mm, 16mm, 25mm

6.2mm liquid lens with auto-focus
Image Resolution (pixels)2 640 x 480 640 x 480 (default) 640 x 480 (default) 640 x 480 640 x 480 (default) 640 x 480
640 x 480 (2x image magnification mode) 640 x 480 (2x image magnification mode) 640 x 480 (2x image magnification mode) 640 x 480 (2x image magnification mode) 640 x 480 (2x image magnification mode)
800 x 600 (2x image magnification mode) 800 x 600 (2x image magnification mode)(default) 800 x 600 (2x image magnification mode) 800 x 600 (2x image magnification mode)
1280x960 (2x image magnification mode) (default)
Bit Depth 256 grey levels (8 bits/pixel) for monochrome models.

24-bit color for color models.
Electronic Shutter Speed 0.001 to 1000 ms
Frames Per Second (FPS) 3 40 FPS

75 FPS for monochrome models.

55 FPS for color models.

75 FPS for monochrome models.

55 FPS for color models.

 75 FPS

75 FPS for monochrome models.

55 FPS for color models.

1280x960 Image Resolution :

40 FPS for monochrome models.

24 FPS for color models.

Other Image Resolutions:

75 FPS for monochrome models.

55 FPS for color models.
Trigger

1 opto-isolated, acquisition trigger input. Remote software commands via Ethernet.

Voltage: ON 15 to 24VDC (24VDC nominal); OFF 0 to 5VDC (0VDC nominal)

Current: 3.6 mA @ 12VDC, 7.5 mA @ 24VDC, Resistance: ~5.48 kOhms
Discrete Inputs

1 opto-isolated general-purpose input line. (7 general-purpose inputs available when using the optional CIO-1400 I/O expansion module4.)

Voltage: ON 15 to 24VDC (24VDC nominal); OFF 0 to 5VDC (0VDC nominal)

Current: 3.6 mA @ 12VDC, 7.5 mA @ 24VDC, Resistance: ~5.48 kOhms
Discrete Outputs

4 opto-isolated high-speed output lines. (2 high-speed outputs, plus 6 general-purpose outputs available when using the optional CIO-1400 expansion I/O module.)

Voltage: 28VDC maximum through external load

Current5: 50 mA maximum ON sink or source, OFF state leakage current 100 µA; External load resistance 240 Ohms to 10K Ohms; Each line rated at a maximum 50 mA, protected against over-current, short circuits and transients from switching inductive loads. High current inductive loads require external protection diode.
Power Consumption

24VDC ±10%, 4.8 W (0.2 A) maximum when illumination is on.

24VDC ±10%, 2.4 W (0.1 A) without illumination.

Note: During illumination-on-time the max. peak current can reach 0.9 A when using high-power illumination modules with exposure time above 0.5 ms.
Status LEDs Power, Trigger Status, Pass/Fail Status, Network and Error
Network Communication EtherNet/IP, PROFINET, SLMP, SLMP Scanner, Modbus TCP, TCP/IP, UDP, FTP, Telnet (Native Mode). Supports DHCP (factory default), static and link-local IP address configuration
RS-232 RxD, TxD according to TIA/EIA-232-F
Material Painted aluminum
Mounting Four M3 threaded mounting holes
Weight 200 g (7.05 oz.)
Temperature

Operating: 0°C to 40°C (32°F to 104°F)

Storage: -10°C to 60°C (14°F to 140°F)
Maximum Humidity < 95%, non-condensing
Protection IP65 when all connectors are attached to cables or shielded by a sealing cap
Shock (Shipping and Storage) IEC 60068-2-27: 1000 shocks, semi-sinusoidal, 11g, 10ms
Vibration (Shipping and Storage) IEC 60068-2-6: vibration test in each of the three main axis for 2 hours @ 10 Gs (10 to 500 Hz at 100m/s2 /15mm)