8505P Vision System Specifications
| Specifications | 8505P |
|---|---|
| Minimum Firmware Requirement | In-Sight 5.9.0 |
| Job/Program Memory | 14.8GB non-volatile flash memory. Unlimited storage via remote network device. |
| Image Processing Memory | 512MB SDRAM |
| Sensor Type | 2/3-inch CMOS, global shutter |
| Sensor Properties | 11.1mm diagonal, 3.45 x 3.45µm sq. pixels |
| Maximum Resolution (pixels)1You can configure the number of image sensor rows and set them in the In-Sight Explorer software. If you decrease the number of rows, it increases the frames per second acquired by the vision system. Refer to the AcquireImage topic in the In-Sight® Explorer Help file for more information. | 2448 x 2048 |
| Electronic Shutter Speed | 21µs to 1000ms |
| Acquisition | Rapid reset, progressive scan, full-frame integration. High Dynamic Range (HDR+) available. |
| Bit Depth | 256 grey levels (8 bits/pixel) |
| Frames Per Second (FPS)2Maximum frames per second are job-dependent, based on the minimum exposure for a full image frame capture using the dedicated acquisition trigger, and assumes there is no user interface connection to the vision system. | 33 FPS |
| Lens Type | C-Mount |
| Trigger | 1 opto-isolated, acquisition trigger input. Remote software commands via Ethernet. (RS-232C available when using the optional CIO-MICRO I/O module.) |
| Discrete Inputs | None. (Eight additional general-purpose inputs available when using the optional CIO-MICRO I/O module.) |
| Discrete Outputs | 2 opto-isolated, NPN/PNP high-speed output lines. (Eight additional general-purpose outputs available when using the optional CIO-MICRO I/O module.) |
| Status LEDs | Network, 2 user-configurable. |
| Network Communication | 1 Ethernet port, 10/100/1000 BaseT with auto MDIX. IEEE 802.3af or 802.3at TCP/IP Protocol.Supports DHCP (factory default), static and link-local IP address configuration. |
| Serial Communication | None. (RS-232C: 4800 to 115,200 baud rates when connected to the optional CIO-MICRO I/O module.) |
| Power |
Class 3 Power over Ethernet (PoE) device. Note: The In-Sight 8505P vision system must be connected to a Class 0, 3 or 4 PoE power source, rated for at least 12.95 Watts. The CIO-MICRO I/O module is a Class 2 PoE device and therefore cannot be used to supply power to the In-Sight 8505P vision system via the I/O module's PoE port.
|
| Power Type | PoE Type A and Type B. |
| Power Consumption | 12.95 W maximum per Class 3 PoE. |
| Current | Per Class 3 PoE requirements. |
| Voltage | 48VDC nominal, applied from a Class 3 PoE source, which is typically powered from some other voltage. |
| Material | Die-cast zinc housing. |
| Finish | Painted. |
| Mounting | Four M3 threaded mounting holes (1/4-20 and M6 mounting holes also available on accessory BKT‑IS8K‑01 mounting bracket). |
| Dimensions | 35.0mm (1.38in) x 32.0mm (1.26in) x 75.55mm (2.97in). |
| Weight |
Vision system with no accessories attached: 192g (6.77 oz.) |
| Case Temperature3To verify case temperature, use the EV GetSystemConfig(“Internal.Temperature”) Extended Native Mode command or GetSystemConfig(“Internal.Temperature”) spreadsheet function. When issued, it returns the vision system's internal temperature in degrees Celsius, which is ~3 degrees above the vision system case temperature. Refer to the In-Sight® Explorer Help file for more information. Additional cooling measures are required if the case temperature cannot be kept below 60°C. Examples of such measures include: mounting the vision system to a heat sink using the M3 mounting screws, reducing the ambient temperature and ensuring there is air flow over the vision system. | 0°C to 60°C (32°F to 140°F) |
| Storage Temperature | -20°C to 80°C (-4°F to 176°F) |
| Humidity | < 80% non-condensing |
| Protection | IP40 with cables and lens attached.
|
| Shock (Shipping and Storage) | IEC 60068-2-27: 18 shocks (3 shocks in each polarity in each (X, Y, Z) axis) 80 Gs (800m/s2 at 11ms, half-sinusoidal) |
| Vibration (Shipping and Storage) | IEC 60068-2-6: vibration test in each of the three main axis for 2 hours @ 10 Gs (10 to 500 Hz at 100m/s2 / 15mm) |
| Regulations/Conformity | CE, FCC, KCC, TÜV SÜD NRTL, EU RoHS, China RoHS |