8405 Vision System Specifications
| Specifications | 8405 |
|---|---|
| Minimum Firmware Requirement | In-Sight version 5.1.1 |
| Job/Program Memory | 512MB non-volatile flash memory; unlimited storage via remote network device. |
| Image Processing Memory | 512MB SDRAM |
| Sensor Type | 1/2.5 inch CMOS, rolling shutter |
| Sensor Properties | 7.13mm diagonal, 2.2 x 2.2µm sq. pixels |
| Maximum Resolution (pixels)1You can configure the number of image sensor rows and set them in the In-Sight Explorer software. If you decrease the number of rows, it increases the frames per second acquired by the vision system. Refer to the AcquireImage topic in the In-Sight® Explorer Help file for more information. | 2592 x 1944 |
| Electronic Shutter Speed | 32µs to 1000ms |
| Acquisition | Rapid reset, progressive scan, full-frame integration. |
| Bit Depth | 256 grey levels (8 bits/pixel) |
| Frames Per Second (FPS)2Maximum frames per second are job-dependent, based on the minimum exposure for a full image frame capture using the dedicated acquisition trigger, and assumes there is no user interface connection to the vision system. | 13 FPS |
| Lens Type | C-Mount |
| Trigger | 1 opto-isolated, acquisition trigger input. Remote software commands via Ethernet. (RS-232C available when using the optional CIO-MICRO I/O module.) |
| Discrete Inputs | None. (Eight additional general-purpose inputs available when using the optional CIO-MICRO I/O module.) |
| Discrete Outputs | 2 opto-isolated, NPN/PNP high-speed output lines. (Eight additional general-purpose outputs available when using the optional CIO-MICRO I/O module.) |
| Status LEDs | Network, 2 user-configurable. |
| Network Communication | 1 Ethernet port, 10/100/1000 BaseT with auto MDIX. IEEE 802.3af TCP/IP Protocol. Supports DHCP (factory default), static and link-local IP address configuration. |
| Serial Communication | None. (RS-232C: 4800 to 115,200 baud rates when connected to the optional CIO-MICRO I/O module.) |
| Power | Class 2 Power over Ethernet (PoE) device. |
| Power Type | PoE Type A and Type B. |
| Power Consumption | 6.49 W maximum per Class 2 PoE. |
| Current | Per Class 2 PoE requirements. |
| Voltage | 48VDC nominal, applied from a Class 2 PoE device, which is typically powered from some other voltage. |
| Material | Die-cast zinc housing. |
| Finish | Painted. |
| Mounting | Four M3 threaded mounting holes (1/4-20 and M6 mounting holes also available on accessory mounting block). |
| Dimensions |
31.0mm (1.22in) x 31.2mm (1.23in) x 71.6mm (2.82in) without accessory mounting block. 39.0mm (1.54in) x 31.2mm (1.23in) x 71.6mm (2.82in) with accessory mounting block. |
| Weight |
78 g (2.75 oz.) without accessory mounting block. 109 g (3.84 oz.) with accessory mounting block. |
| Case Temperature3Case temperature can be verified using the EV GetSystemConfig(“Internal.Temperature”) Extended Native Mode command. When issued, it returns the vision system's internal temperature in degrees Celsius, which will be ±5 degrees above the vision system case temperature. Refer to the In-Sight® Explorer Help file for more information. Additional cooling measures are required if the case temperature cannot be kept below 50°C. Examples of such measures include: mounting the vision system to a heat sink using the M3 mounting screws, reducing the ambient temperature and ensuring there is air flow over the vision system. | 0°C to 50°C (32°F to 122°F) |
| Storage Temperature | -20°C to 80°C (-4°F to 176°F) |
| Humidity | < 80% non-condensing |
| Protection | IP30 with cables and lens attached. |
| Shock (Shipping and Storage) | IEC 60068-2-27: 18 shocks (3 shocks in each polarity in each (X, Y, Z) axis) 80 Gs (800m/s2 at 11ms, half-sinusoidal) |
| Vibration (Shipping and Storage) | IEC 60068-2-6: vibration test in each of the three main axis for 2 hours @ 10 Gs (10 to 500 Hz at 100m/s2 / 15mm) |
| Regulations/Conformity | CE, FCC, KCC, TÜV SÜD NRTL, EU RoHS, China RoHS |